C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END MILL,HI HELIX CC END MILL C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE, BUT NOT ON CUTTING EDGES,(C-4-6-1-11) INDUSTRIAL SURPLUS, THIS IS A NEW NEVER USED 3/8 X 3/8 X 3/4 X 2 5/8 2FL CC HIGH HELIX END MILL, MADE BY UNION BUTTERFIELD -LIKELY M7 HSS, THESE HAD CORROSION ON MILLED SURFACES (FROM LONG STORAGE).MILL C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END.

C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END MILL




C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END MILL

3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END MILL (C-4-6-1-11). (C-4-6-1-11) INDUSTRIAL SURPLUS, THIS IS A NEW NEVER USED 3/8 X 3/8 X 3/4 X 2 5/8 2FL CC HIGH HELIX END MILL, MADE BY UNION BUTTERFIELD -LIKELY M7 HSS. THESE HAD CORROSION ON MILLED SURFACES (FROM LONG STORAGE), BUT NOT ON CUTTING EDGES.. Condition:: New other (see details): A new, unused item with absolutely no signs of wear. The item may be missing the original packaging, or in the original packaging but not sealed. The item may be a factory second or a new, unused item with defects. See the seller’s listing for full details and description of any imperfections. See all condition definitions : Brand: : Union Butterfield , MPN: : Does Not Apply ,

C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END MILL

C-4-6-1-11 3//8 X 3//8 X 3//4 X 2-5//8 2 FLUTE HI HELIX CC END MILL
C-4-6-1-11 3//8 X 3//8 X 3//4 X 2-5//8 2 FLUTE HI HELIX CC END MILL

C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END MILL

2000W AC 50-220V 25A Motor Speed Controller Adjustable Motor Speed Controller, 800-1000KV Ultra-High Voltage Pulse Generator DC Super Arc Module 4A 3.7-7.4V. PLUG & BOTTOM GH3 Machinist NEW USA CLEVELAND HSS 3pc 11/16"-16 TAP SET TAPER. Schneider/Telemecanique LC1D65AB7 Magnetic Contactor AC24V, NEW IN BOX ITW 100710 100710. 50PCS 50V 22uF 50Volt 22MFD Electrolytic Capacitor 5mm×11mm. Low-Dropout 1.0~16 V Regulator TO-252 5PCS 3010KM SI3010KM SI-3010KM 1 A. 10mm*19mm*5mm 10PCS 6800-2RS 6800RS Deep Groove Rubber Shielded Ball Bearings. SOT-23-3 -150V 5PCS X SI2325DS-T1-GE3 SI2325DS-T1 MOSFET -0.53A P-CH. M3-0.50 Knurled Point Socket Set Screws Alloy Steel w/ Black Oxide DIN 916. 9007 9004 Car Headligh Female Wire Harness Connector Pigtail Plug Socket Adapter. 10PCS Yellow 2.54mm 40 Pin Male Single Row Pin Header Strip, IAI IADP3203020 IAI IADP3203 IAI Linear Actuator Controls BOARD IAI BOARD, 1/2" Dr Drive Air Ratchet Right Angle Impact Wrench Tool. Washer M4 304 Stainless Steel Allen Hex Socket Head Cap Screw Bolt Hex Nut. 6-24V Flip-Flop Latch Relay Bistable Self-locking Low Pulse Trigger Module 1PC.12" 2-Jet S-Bend Regular ProfIle Wand 1.5" carpet cleaning extractor cleaning, heavy duty Shallow Well Jet Pump w/Pressure Switch 1/2HP 12.5GPM 115/230V. 100pcs Mix Oscillating Saw Blade For FEIN,BOSCH,Dremel,Makita Multi tool. Fairchild TD6000-75 Electric To Pneumatic Transducer 65-150 PSIG electro T6000, Moving Shrink Wrap 12 Rolls Black Color Pre-Stretch Film 17" x 1476' x 8.5 Mic, 1pc D3.175mm 1/8" 2Flute HRC55 Up&Down Cut Solid Carbide wood end mill tool, White Wove Diagonal Seam Regular 3⅝" x 6½" Envelopes #6¾ 24lb 5,000 Per Ctn.

C-4-6-1-11 3/8 X 3/8 X 3/4 X 2-5/8 2 FLUTE HI HELIX CC END MILL
BUT NOT ON CUTTING EDGES,(C-4-6-1-11) INDUSTRIAL SURPLUS, THIS IS A NEW NEVER USED 3/8 X 3/8 X 3/4 X 2 5/8 2FL CC HIGH HELIX END MILL, MADE BY UNION BUTTERFIELD -LIKELY M7 HSS, THESE HAD CORROSION ON MILLED SURFACES (FROM LONG STORAGE).